Frequently Asked Questions

Does your scooter need a service?

A general service includes:
  • Removing the bars & fork
  • Check the headset bearings & clean.
  • Check headset, sleeve & dust cap for damage.
  • Dial in the headset again.
  • Check condition of the brake & fasten if required.
  • Check wheel bearings, front & back (2 per wheel).
  • Fit anything additional the customer requires, such as grips, bar ends, wheels, bearings, grip tape, sticker etc.
  • General clean of the scooter - wheels, bars & deck.

Service = R300 (Excludes parts needed)

Custom services & upgrades also available, contact us for a no obligation quote.

Other services:

  • Paint refurbishment on request (Currently not available for Neo chrome or chrome finishes)
  • Chopping of handle bars to accommodate younger riders

Replacement Parts

Abec-9 100mm wheel bearings = R50 each (2 per wheel)

Abec-9 110mm wheel bearings = R50 each (2 per wheel)

Headset bearings set = R200 each (R100 each)

Abec-9 wheel bearing set = R250 (100mm & 110mm)

100mm wheels = R690 per set (Includes bearings)

110mm wheels = R980 - R1250 per set (Includes bearings)

Park deck grip tape with logo = R120

Street deck grip tape without logo = R120

Handle bars = R980 - R2600 each (Excludes grips)

2 Bolt headset clamp = R380 - R460 each

3 Bolt headset clamp = R380 - R460 each

Conversion sleeve = R220 (IHC to HIC) - M6 & M8

Compression sleeve kit = R240 (IHC & HIC)

Complete headset kit = R350 (Sleeve, spacer. cap & bolt)

Fork = R850 (IHC & HIC) - Accomodates SCS bars

Rear wheel brake (100mm & 110mm) = R220 each

Rear wheel fender (100mm & 110mm) = R240 each

Bar grips = R200 - R280 per set

Bar end caps = R25 per set

Wheel pegs = R380 - R440 per set (1 wheel)

Fork spacers = R70 each

Inner wheel spacers = R25 each

Wheel axles = R80 each

Brake & fender screws = R15 per set (2 per brake)

Various stickers = R10 each

Does your scooter need a new lick of paint?

We offer refurbishments of Decks, clamps, bars & forks.

DECKS

The process includes stripping off the old paint layer. In the case of standard colours such as black, blue or white, a process of bead blasting is used. This will not only remove the old paint but improve the surface, making small scuff marks & scratches smoother. It is important to not that we are redoing a used deck, so dents, deep scratches & gashes will not be rectified. Once this is done a new powder coat layer is applied. Chrome or Neo chrome scooter cannot be refurbished in the same finish but can be removed to apply a standard colour.

BARS

The same process applies here except for the fact that we cannot refurbis the chrome, neo chrome & titanium bars with the same finish. Unless it a case where the chrome, neo chrome ot titanium finish is to be covered with a standard colour of poweder coating.

CLAMPS & FORKS

These are anodized & will be re-anodized. Except in the case of chrome & neo chrome finishes where it can be stripped for a new standard powder coating.

NOTES

  • Seven standard colours to choose from.
  • Chrome & Neo chrome coating not available.
  • Refurbishment is not available for polished chrome, neo chrome & titatium bars.
  • Deep scratches, dents & gashes cannot be repaired completely.

Basic refurb = R500

Advanced refurb = R750

  • BEFORE

    Scuff marks on the deck, fork, clamp & bars. Still has old red core wheels.

  • AFTER

    Resprayed deck, fork, clamp & bars. Customer also replaced the wheels.